How to glue a shiny film on an iPhone. Applying a protective film to the iPhone screen. Preparation of the workplace

There is nothing sadder than looking at a magnificent Retina display new model iPhone smartphone through a giant scratch running through the center of the screen. Apple guarantees the high strength of the glass used in the iPhone, but it can still break and be scratched. How can you reduce the risk of such unpleasant incidents? After all, removing a scratch from glass is almost impossible. It's best to take care of your handset in advance and stick a protective film on your iPhone.

Below are instructions for installing an Epic protective film on an iPhone 5. You can also use the recommendations given for films from other manufacturers.

1. Unpack the protective film

Carefully open the paper or plastic packaging with protective film. In paper packaging, simply tear off the strip that says “open.”

2. Clean the iPhone screen

Using a microfiber cloth (often included with a protective film), we thoroughly clean the smartphone screen. There should be no dust particles or fingerprints on it.

This is a very important step, and its implementation should be approached with all responsibility. Once the protective film is applied, it will be impossible to remove the dirt underneath.

3. Trying it on

Before you delete additional elements screen protector, make sure it fits your iPhone screen size well. Start from the bottom edge. Position the film so that the cutout neatly surrounds the Home button. You should also ensure that the hole opposite the speaker is positioned correctly and how carefully the edges and corners of the film are positioned.

The cut of the top edge should not overlap the ambient light level sensor.

Small deviations from the ideal film position are acceptable. They will not interfere with the operation of the device and will be practically invisible during its operation.

4. Start gluing

Holding the protective film in one hand, pull the label, which is usually marked with the number “1” or the inscription “Step 1”. We release the very top part of the protective film from the additional element.

5. Starting from the top

We start gluing the film from the top edge. Carefully place the uppermost part of it on the surface of the glass. We check how accurately the corners fit into the intended points. After this, press the film against the screen so as not to move it.

6. Top to bottom

With one hand we gradually remove the additional film, and with the other we carefully and slowly lay the protective film on the screen, making sure that its edges lie parallel to the edges of the case.

After this, we begin to remove the bottom additional film. In a minute or two, the protective film will be completely fixed on the front surface of the iPhone.

7. Remove bubbles

Using a special rubber device, usually included with the film, we remove air bubbles from under the protective film. We “drive” the bubbles to the edge and release them “into the wild.”

However, not all bubbles will “want” to be removed. It’s okay, within 24 hours they should disappear on their own, leaving no traces.

8. “Burning Bridges”

If the protective film is positioned as intended, then remove the second tab at the top of the screen. It is usually marked “2” or “Step 2″.

So we installed a protective film on the front surface of the iPhone 5!

9. Protective film on the rear window

In a similar way, you can protect the back glass of your smartphone.

10. How to remove a speck of dust from under the protective film of iPhone 5

If a speck of dust is found under the protective film, you should use a small strip of regular office tape. Glue it to the edge of the protective film closest to the speck of dust and carefully lift it up.

11. Catching a speck of dust

Using a second piece of tape, we “grab” the speck of dust and remove it from the surface of the screen.

After this, carefully return the protective film to its place.

Now we don't have to worry about scratches on the screen of our iPhone 5.

A protective film for iPhone is the first thing every new owner should think about. of this device. Thanks to high quality film iPhone screen Protects against cuts from keys in your pocket, abrasions due to less than careful handling, for example, when the iPhone is placed face down on a table, and also from fingerprints. The film allows you to keep the device’s display in its original form, which is not only pleasant during use, but will also help sell the device profitably.

There are different films for iPhone, but they differ only in their quality and coating material. The gluing process is the same for all films, so we will not consider film models various manufacturers, but we’ll still tell you about the material covering the top layer of the film.

iPhone screen protectors come in three main types:

• matte - easily cope with glare on the screen. Ideal for use in constant bright sunlight
• glossy – improve the iPhone picture. Images on the screen when using such protective films will become brighter and more contrasting.
• mirrored – give the iPhone display a very beautiful look appearance

These are the three main categories of iPhone screen protectors. Additional properties, such as self-healing or antibacterial coating, are just bells and whistles that manufacturing companies build into their films, giving them greater value.

The film has been chosen, all that remains is to paste it correctly. In some stores, employees may offer you help in applying the protective film and it is better not to refuse it. An experienced specialist will paste the film perfectly evenly and will not spend much time on it. If such an offer has not been received, you can inquire about providing such a service to you. But if suddenly you find yourself at home with an unpacked protective film in your hands, gather your thoughts and begin this simple but painstaking process.

How to stick a film on an iPhone

Step 1: Unpack the protective film. Any film for iPhone includes the protective film itself, a microfiber cloth and a special device for removing bubbles from under the film (can be plastic or rubber)

Step 2: Clean your iPhone display. This must be done using the included microfiber cloth. Carefully, in a circular motion, remove all greasy marks and dust particles from the device screen - the better you clean the screen, the better your iPhone will look after gluing the film.

Step 3: Try the film on your iPhone screen. It’s too early to pull the labels pasted on the film - first you need to make sure that the film is the right size and figure out a plan according to which you will glue it. Try to navigate by the Home button and the speaker cutout, this will allow you to stick the film as accurately as possible

Step 4. We begin to apply the protective film. Take the film in one hand, and with the other pull the tab with the number 1 drawn (it may also say Step 1. Remove me!). By removing the first layer of film you will “expose” the adhesive surface, so be careful! Under no circumstances should you place the film on the table, and in general, try not to let dust get on the sticky surface.

Step 5. We begin to glue the film. Start applying the film from the top edge of your iPhone. Using the side edges and speaker connector as a guide, place the film evenly on the surface of the glass. Attention! If the film lays unevenly the first time, it’s okay. Carefully peel it off the surface and try to paste the film again - the film will not lose its adhesive properties even after several such failures, but do not overuse it

Step 6. Add the film. Apply the protective film lower and lower, at the same time, slowly, smoothing the area to be pasted. Try not to make sudden movements, otherwise you risk creating a bubble that will not be so easy to remove. Make sure that the film is laid parallel

Step 7. Remove bubbles. After the film is completely pasted, do not rush to remove the second protective layer. Armed with the special device for removing bubbles that came with the kit, carefully begin to drive the bubbles to the edge of the screen. Try to achieve the maximum result - most likely you will have to spend some time on this. Attention! Don’t forget to separately go through the place where the second label is located

Step 8. Remove the second protective layer. While holding the film, pull the last remaining tab and remove the entire top protective layer. It is necessary to hold it if the film does not lie firmly enough, but it is better to be on the safe side.

After removing the film, you can proudly see the result of your work; we hope that you will be able to stick the protective film on your iPhone smoothly and without large bubbles. However, bubbles are not the worst problem; specks of dust are much more serious.

How to remove a speck of dust from under an iPhone screen protector

Step 1. Take stationery tape (the narrow version) and cut a small piece. Apply the tape to the place closest to the speck of dust and carefully lift the protective film. Protective films sometimes come with specially prepared pieces of tape that you can use in this situation.

Step 2. After lifting the film, do not lift it very high so that new foreign objects do not get under the film. Using the second piece of tape, carefully catch the hated speck of dust. Attention! You should not try to catch a speck of dust with tongs or other sharp objects - you risk scratching the protective film.

Step 3. After removing the dust, slowly return the film to its place, smoothing out any bubbles that appear

In the same way, you can remove accidentally fallen hair and other foreign objects from under the protective film. The process of applying an iPad screen protector is the same as described above, but requires much more concentration due to the large screen area. Protective film on back cover devices are glued using a similar technology.

Also interesting:

• How to turn off bluetooth on iPhone?
• The Way to Increase iPhone Battery Life That Everyone Forgets About
• Beeline Internet on iPhone

Please rate this article 5 stars if you like this topic. follow us

To displays mobile devices- not a pleasant task. Read about how to ideally apply film for iPhone and iPad in this material.

Modern protective films are so thin that the slightest speck of dust on the display will leave behind a bubble, which will be quite difficult to remove. The process is quite complicated, but using the tips below, this delicate operation will not cause you any difficulties.

How to perfectly apply a protective film on iPhone and iPad

1 . We wash our hands thoroughly. Dust, dirt and, of course, grease are the first signs of a poorly applied protective film.

2 . Wipe the work surface where you will be gluing the film.

3 . Perfectly clean the surface iPhone display or iPad. Microfiber cloths work best for this. This fabric absorbs moisture well and does not leave fibers behind.

4 . Get a bubble scraper. They usually come complete with film. If you don’t have one, then a bank card will do.

5 . Attach the film to the display. It's no secret that screen protectors are covered with films on both sides. They usually have stickers on them indicating the extraction order. Applying the film to the display at the bottom with two pieces of tape, fix it to the device so that there are no distortions when gluing.

6 . Lift the screen protector and, holding it in a vertical position, wipe the display with microfiber again.

7 . Start shooting your first film...

and at the same time stick the film to the display

Perform the operation slowly to avoid the formation of bubbles.

7 . At the very end, remove the remaining bubbles with a scraper/card.

Using this method, there is a high probability of sticking the film perfectly.

A mobile phone is a fragile device that will develop scratches and other things over time. This significantly spoils its appearance. He becomes unsightly and unkempt. And many people know that you can tell a lot about a person just by looking at his phone number. Therefore, for many, the problem of protecting the phone from mechanical influences and other things that worsen his external data.

She has a solution. It is enough to use auxiliary devices. For example, a cover. He is able to protect as one specific element the device, and all of it from scuffs and other damage.

Screen Protective Film: Basic Functions

One such method is to apply film to the screen. It protects against scratches, abrasions, etc., which cannot be avoided even with the most careful handling of the device. And it doesn’t matter at all who made it. Even the most famous and popular company, Apple, recommends using a screen protector, as it will preserve the original appearance of the product for a very long time. Although this product has one drawback - the film reduces the quality of visibility. It is worth noting that it is insignificant, and in principle the human eye is not able to perceive the difference when it is on the screen and when it is not.

How to apply film to an iPhone: who to trust?

Applying film to an iPhone is not easy. This is painstaking work that requires care and precision. Otherwise, bubbles will form on the screen. They spoil its appearance and indicate poor quality of this work.

The film is mainly glued by specialists from the store where the goods are purchased. But you will need to pay separately for this. The cost of this service is equal to the price of the film. In this case, the specialist is responsible for it. In case of poor quality work, you can demand that they redo it. Moreover, everything must be done at their expense.

If you decide to save money, you can stick the film on the iPhone yourself. But it’s better to calculate your strength from the beginning. Will you be able to do this? As practice shows, if you do it carefully and know the features this process, then everyone can do it.

How to properly glue film to an iPhone: preparatory activities

You don't need any special equipment or tools to apply the film to your iPhone. Therefore, this can be done at home. The first thing to start with is to put your phone on the table. Then point the lamp at it. It's better if it's in daylight. This will allow you to determine whether there are dust or lint on the screen.

Then you need to wipe it with the microfiber cloth that comes with the phone. You can do this with a special spray that is used for cleaning similar devices. But it must be purchased separately. It is available in many stores that sell computers. For this purpose, it is strictly forbidden to use products that contain alcohol, as this will be harmful to the device’s screen.

Make sure the screen is clean. It should be free of fingerprints, grease stains, dust and other dirt. Particular attention should be paid to the presence of solid particles. They are extremely unsafe for the screen.

After completing this work, you need to take out the film that is in the package. This is done carefully so as not to damage it. Then you should take a good look at it. So, on its corners there are stickers that will be used.

How to properly glue film on an iPhone: features of the process

To start working with the film, it is placed on the table. In this case, its surface must be dry, smooth and clean. The paper stickers are not firmly attached and are easy to peel off. But it is worth paying attention that this is done centimeter by centimeter. Moreover, you cannot touch the adhesive side of the film with your hands. This may leave stains and other unwanted marks on it.

The film is then applied to the phone screen. Clarity is important here. Therefore, the corners of the two surfaces must coincide. Next, the free edge of the film is pressed well against the screen. If on initial stage If irregularities appear, it is better to remove the film and start all over again, since doing this further will be problematic. This manipulation can be carried out several times until the desired result is achieved. At the same time, it will not deteriorate in any way and will not lose its appearance. But you can’t overdo it, as dust and other dirt may get on it. The adhesive side of the film quickly grabs them. If this happens, then it becomes unsuitable for further use. Therefore, it is better to throw it away and get a new one.

After this, the entire film is glued. Bubbles often appear in this process, even among professionals who do this work every day. No need to worry - this situation can be fixed. They can be removed using a plastic card - it is swiped across the phone screen, and this must be done from the center to the edge. Such simple procedure This will get rid of all the bubbles and unwanted air under the film.

The final stage is the removal of the second film, which acts as an auxiliary film. Moreover, it is better to do this with a sticker. But it must be the second one.

Do I need to put a film on my iPhone?

Do I need to put a film on my iPhone? This is one of the most frequently asked questions. Since everyone knows about high quality of this product. But, as practice shows, the film must be glued to any screen. And it doesn’t matter whether it’s a phone or a tablet, since you will carry it in your pocket, purse or other place. At the same time, it can get rubbed and scratched, which will ruin its appearance. After a year of operation it will change. This is an undesirable effect. Only a protective film will help protect your iPhone screen. Moreover, only you will know about its existence. To identify it to a stranger, you need to look carefully; it is unlikely that he will do this. The film is transparent, so the design and other data of the phone will remain unchanged.

Screen protectors are the cornerstone. Many people think that it is simply impossible to stick it properly, especially on their own. Others calmly do it with their own hands and remain in the status of possessors of “secret knowledge.” But in reality, it's really quite simple: you just need to learn a few secrets.

The brief instructions that usually come with the film are usually useless. It is unknown who came up with the idea of ​​writing the cherished “Paste the film evenly and without bubbles,” but this “someone” clearly did not know about the difficulties and suffering that accompany this process. Try putting the instructions aside and doing things differently.

First, wipe the smartphone screen with an alcohol wipe or microfiber. Moreover, take your time and rub more thoroughly so that not a single microbe remains on the screen. Now life hacks. The first secret is to secure the film to the screen before you peel off the protective layer. This will minimize the possibility of dust getting under the film before gluing. And it will be more convenient to work.

Place the film on the phone and secure it around the edges with electrical tape, leaving one side free. Lift the film by the free edge and carefully peel off the protective layer.

The main thing you need to try to avoid is the ingress of dust and the formation of air bubbles. Therefore, stock up on a credit or any other plastic card before gluing the film. Help yourself with this “tool” by pressing the film tightly while gluing. Smooth it with a card and make sure that air does not penetrate under the coating. If dust does end up under the film, do not peel it off! Secret number two: instead of re-gluing everything, push the dust to the very edge of the film, pressing the edge of the plastic card firmly against the screen.