Arrow indicators of sound signals. Forex sound indicator - comfortable trading Indication of sound signals

Dial indicator of output signal level

Today, as an indicator of the output signal level for various sound reproduction equipment, entire electronic devices, which display not only the signal level, but also other useful information. But previously, dial indicators were used for this, which were a type of microammeter M476 or M4762. Although I will make a reservation: today some developers also use dial indicators, although they look much more interesting and differ not only in backlighting, but also in design. Getting hold of an old dial indicator might be a problem now. But I had a couple of M4762 from an old Soviet amplifier, and I decided to use them.

On Fig.1 A diagram for one channel is presented. For stereo we will need to assemble two such devices. The signal level indicator is assembled on one transistor T1, any of the series KT315. To increase sensitivity, a voltage doubling circuit was used on diodes D1 and D2 from the D9 series. The device does not contain scarce radio components, so you can use any with similar parameters.

The indicator reading corresponding to the nominal level is set using trimming resistor R2. The integration time of the indicator is 150-350 ms, and the return time of the needle, determined by the discharge time of capacitor C5, is 0.5-1.5 s. Capacitor C4 is one for two devices. It is used to smooth out ripples when turned on. In principle, this capacitor can be abandoned.

The device for two audio channels is assembled on printed circuit board dimensions 100X43 mm (see Fig.2). Indicators are also mounted here. For easy access Holes are drilled into the board for the construction resistors (not shown in the figure) so that a small screwdriver can pass through to adjust the nominal signal level. However, that’s all the setup comes down to. of this device. You may need to select resistor R1 depending on the output signal strength of your device. Because On the other side of the board there are dial indicators; elements Cl, R1 had to be mounted on the side of the printed circuit conductors. It is better to take these parts as miniature as possible, for example, unframed.

The unprecedented speed of profit generation, which is demonstrated by options such as turbo, or regular options with a short expiration time, makes them the most highly profitable trading assets of all existing on the exchange.

However, the speed of making a profit goes hand in hand with the speed of making a loss, from which no one is insured without applying the proper strategy.

And, if on long-term transactions, luck may accompany you for some time, then as soon as you start scalping, after the first few transactions you will realize that without a proper strategy you have nothing to do in this market -)

Therefore, today I propose Learn and apply the WPRSI Signal strategy, which is tailored specifically for scalping in difficult to predict conditions...

WPRSI Signal is a universal scalping strategy based on a number of technical indicators, which, thanks to a simplified approach to signal interpretation, will allow you to scalp financial markets even the greenest beginners.

Moreover, the strategy will allow you to significantly diversify your risks, due to the fact that it is effectively used on Forex in its original form to this day.

Performance characteristics of the strategy

• Trading time – with increased volatility for your asset;
• Assets - almost everything, the main thing you should pay attention to is the payout percentage for the option, which should be at least 75 percent;
• The timeframe of the test chart is M1 or, as a last resort, M15 (increasing the timeframe reduces the number of signals);
• Expiration – from a minute and above (pay attention to!);
• Brokers for trading - I recommend only.

You can download WPRSI Signal, indicators with a strategy template, by clicking the button below:

Key information on indicators

Many people make a huge mistake when trying to adapt complex strategies for binary options scalping. In fact, the fewer factors that distract attention from price, the better.

Yes, often, complex strategies seem effective in theory, but in practice they are a complete waste. And, of course, vice versa.

In our case, the strategy has three indicators, although in fact only two are important.

1. WPRSI Signal indicator- this is an interesting symbiosis of two oscillators, WPR (Williams Percent Range) and, which is designed in the form of a pointer, signal indicator.
   It is worth noting that these two indicators seem to filter each other, so signals appear less frequently, but their accuracy is an order of magnitude higher than if we used them individually;
2. FXPT DBL top bottom — a simple technical assistant that marks the minimum and maximum of a certain price movement, creates support and resistance levels;
3. FPS Trend is the only trend indicator in the strategy that allows you to track changes in the medium-term and short-term trend. In the settings, you can enable a sound alert that will signal if such a change occurs.

WPRSI Signal Strategy Signals

Based on my observations, WPRSI Signal indicator does not redraw after the candle appears and closes, so if you are faced with a situation with a sharp price surge, you don’t have to wait for the candle to close, but act immediately!

UP signal (CALL)

1. A blue upward arrow from the WPRSI Signal indicator appeared on the chart;
2. The blue FPS Trend bar confirms the upward vector of the trend movement.

If the signal appears near the FXPT DBL top bottom lines or seems to be repelled from them, this is signal amplifying factor.

P.S. I accidentally came across an interesting video - cryptocurrency sectarians in the Moscow region performed a magical ritual of expelling the dollar by burning banknotes while dancing with tambourines -)))

Many sound-reproducing devices, whether tape recorders or amplifiers of the end of the last century, were equipped with a dial indicator on the front panel. Its hand moved to the beat of the music, and although it had no practical meaning, it looked very beautiful. Modern equipment, in which compactness and high functionality come first, no longer has such luxury as a dial indicator for sound. However, it is now quite possible to find a pointer head, which means that such an indicator can be easily assembled with your own hands.

Scheme

Its basis is the Soviet K157DA1 microcircuit, a two-channel full-wave average signal rectifier. The supply voltage of the circuit lies in a wide voltage range, from 12 to 16 volts, because the circuit contains a 9 volt stabilizer (VR1 in the diagram). If you use a stabilizer in metal case TO-220, then the voltage can be supplied up to 30 volts. Trimmer resistors R1 and R2 regulate the signal level at the input of the microcircuit. The circuit is not critical to the ratings of the components used. You can experiment with the capacitances of capacitors C9, C10, which affect the smooth movement of the needle, as well as with resistors R7 and R8, which set the return time of the needle. In L and In R in the diagram are connected to a sound source, which can be any device with linear output– be it a computer, player or phone.

(downloads: 265)

Circuit assembly

The indicator board is manufactured using the LUT method on a piece of textolite measuring 30 x 50 mm. Just in case, the microcircuit should be installed in the socket, then it can be replaced at any time. After etching, the board must be tinned, then it will look beautiful from the side of the tracks, and the copper itself will not oxidize. First of all, small parts are sealed - resistors, ceramic capacitors, and only then electrolytic capacitors, trimming resistors, and a microcircuit. Lastly, all connecting wires are soldered. The board contains two channels at once and involves the use of two arrow heads - for the right and left channels, however, you can use one arrow head, then the input and output contacts for the other channel on the board can simply be left empty, as I did. After installing all the parts on the board, be sure to wash off all remaining flux and check adjacent tracks for short circuits. To connect the board to the signal source, it is most convenient to use a 3.5 jack plug. In this case, if the length of the wires from the board is large (more than 15 cm), a shielded wire should be used.

arrow head

Finding Soviet pointer heads on sale now is not difficult; there are many types of them, in different shapes and sizes. I used a small M42008 pointer head, it doesn't take up much space and looks nice. Any head with a total deflection current of 10-100 microamps is suitable for this circuit. To complete the picture, you can also replace the native scale, calibrated in microamps, with a special sound scale, calibrated in decibels. However, you need to connect the pointer head to the circuit not directly, but through a trimming resistor with a nominal value of 1-2 megaohms. Its middle contact is connected to any of the outer ones and connected to the board, and the remaining contact is connected directly to the head, as can be seen in the photo below.

Setting up the indicator

When the board is assembled, the pointer head is connected, you can begin testing. First of all, by applying power to the board, check the voltage at pin 11 of the microcircuit, there should be 9 volts. If the supply voltage is normal, you can apply a signal from a sound source to the board input. Then, using resistors R1 and R2 on the board and a trimming resistor at the pointer head, achieve the required sensitivity so that the pointer does not go off scale, but is approximately in the middle of the scale. This completes the basic setting, the arrow will move smoothly to the beat of the music. If you want to achieve sharper arrow behavior, you can install resistors with a resistance of 330-500 Ohms parallel to the arrow heads. Such an indicator will look great in the housing of a homemade amplifier, or as a stand-alone device, especially if you illuminate the indicator with a pair of LEDs. Happy building!

Recently, Forex sound indicators have become increasingly used in the process of online trading. This is probably not even the last round of development in terms of convenience of trade. It’s worth clarifying right away that sound alerts are just a factor of convenience, and not the latest algorithm for calculating pricing. A novice trader, going to Forex and hearing the phrase “sound indicator”, can think whatever he wants. Therefore, it’s worth simply describing what Forex sound indicators are and whether they should be used as the basis of trading strategies.

Forex sound indicators that emit sound signals are no different from a regular indicator, only silent. This means that if a sound function is introduced into the algorithm for constructing an indicator, then the signals that it generates will simply be notified by a sound signal. Although, in principle, these may not only be signals to open a transaction. The sound can be produced at any moment set in the indicator. This depends on the indicator itself.

The image highlights the moments of overbought and oversold, which are shown by the RSI indicator. For example, in order not to monitor the chart visually, while constantly being near the monitor, a formula is simply entered into the structure of the indicator. Then, when the line crosses levels 70 and 30, and in the opposite direction, a sound signal will simply sound, indicating the market’s readiness for a possible reversal and thereby concentrating the trader’s attention on the emergence of a trading situation.

But you can make it so, for example, that a sound signal will be issued when the fractal itself appears. So, if this is an interval of 15 minutes, then instead of, say, sitting near the monitor for two hours, it will be enough to simply approach a couple of times at the sound signal.

Or here is another example with the MASD indicator. The archives contain a derivative indicator with a sound alert. When the moving average crosses the histogram, a sound alert is issued. But looking at this indicator in more detail, it would be possible to refine it and make it so that the appearance of a smaller histogram line would also produce a sound signal. The result will be the following combination:

Now, if the first alert sounds, it means the market is turning around, and when the second alert sounds, it already means that it’s worth making some decisions. In general, the picture is not bad, it remains to be seen whether you will have the patience to simply not look into the market until the sound signal. In fact, this is very convenient if you are doing other things or are close to the computer.

It is in this way that Forex sound indicators provide the convenience of monitoring the state of the market through expressing the indicators of the indicator itself.

It is impossible not to note such a nuance as the use of sound indicators in the trading system. It would seem that there is nothing complicated about this. But this is not entirely true. If a trading strategy includes, say, one indicator, then you should set the sound alert exclusively to the one that plays a basic role in the trading process. That is, if the sound signal of the main indicator has passed, only then should you approach and pay attention to the current situation. If everything is quiet, and a secondary indicator shows a signal, it is worth remembering that it is not the main one in the trading system. That is, the principle is still the same, but with sound, as they say, it’s more convenient. And the most important thing is to understand that the essence of the sound signal, whether it is to open an order or to close it, is no different from the usual one, with the exception of the sound.

Thus, Forex sound indicators give us the opportunity to make trading more convenient and calmer. Moreover, more free time appears, which can be used to strengthen your theoretical knowledge or just relax and do something else. Source:

Social buttons for Joomla

Popular:

• 11/14/2013 06:32 | Reversal indicator - determining the end of the trend 57909
• 04/02/2015 10:04 | The VSA indicator reads the market like an open book 55665
• 09.23.2014 11:08 | The Forex advisor designer will allow you to create any trading robot 50382
• 12/13/2013 01:48 | Intraday trading - hourly forex strategy 42500
• 12/12/2014 05:36 | Option Level Indicators – Steps to Your Success 36679
• 09.12.2013 10:37 | Forex indicators without redrawing 32464

Among the huge selection of indicators, there is a special group of tools - profitable forex indicators with sound alert(alert). Basically, these are signal and dial indicators. The convenience of this type of indicator, I think, is obvious. They free the trader from constantly monitoring the market situation. A sound notification will return it to the trading terminal when it is really necessary. As a rule, such indicators are easy to use and have simple settings.

In this article I bring to your attention profitable indicators with sound alerts, which you can use in your trading.

There are several types of sound alerts. These are sound signals when two lines of any indicator cross each other, when the direction of price movement changes and an arrow appears on the chart. Also, sound alerts are used when the price reaches or crosses an important level and when the position of the indicator changes relative to the price level.

Overview of indicators with sound notification

This is a signal indicator. Its signals are formed based on the intersection of three moving averages, which indicates a possible change in the direction of price movement. Moreover, there are three types of signals. If an arrow appears on the chart, it means that the slow and fast MAs have crossed. If the fast and average MAs intersect, we will see a diamond on the chart. And finally, a dot will indicate the intersection of the average and slow MAs.

You can learn about the appearance of signals by a sound alert, and at the same time a message will appear on the monitor:

The indicator has an MTF function, thanks to which it can track the intersection of moving averages on the desired TF without switching to it.

Download indicator 3 MA Cross with alert: 3-MA-Cross-with-alert-mtf-3.03

Parabolic SAR Color - Alert indicator

One of the basic Parabolic SAR indicators is presented in a modified form. Not only is it easier to perceive visually, but it also eliminates the drawback of lag. It beeps when the location of the points relative to the price changes. This is very convenient, since an important point will not be missed by the trader. As in the previous indicator, a message will appear in the terminal along with a sound alert.

QQE histo indicator - alerts

This is an optimized version of a profitable indicator. To consider the possibility of entering the market, the indicator crosses the zero level, as well as the color of the histogram changes. And to ensure that the trader does not miss these signals, the indicator provides a sound alert.

This indicator also has an alert. It differs in that it can be used both in the Forex market and in binary options trading. Its advantages are that, firstly, the algorithm contains a high-quality noise filter, and secondly, it does not lag and therefore its signals are quite accurate. According to available statistics, using this indicator in trading allows you to get more than 100% profit in a year, which is not bad at all. The appearance of a visual signal in the form of an arrow is accompanied by an audio alert.

I can offer you other profitable Forex indicators with sound alerts, which you can find online if you wish.

VR Alert indicator. It beeps when the price crosses a significant level.

Heiken Ashi MA indicator jurik new_alerts. This is a modification of the standard Heiken Ashi, which provides an audio alert.

If you trade on news, then the indicator can be your best assistant Urdala News. It not only displays news on a graph and displays its importance, but also gives a signal. Moreover, the trader can specify in the settings how many minutes before the news release should be notified. So you'll never miss important data.

As you can see, the choice of Forex indicators with alert is very large. A sound notification will make trading more comfortable for the trader, and this is one of the components of success.