ASUS network and server equipment. Firmware, catalogs. “Here’s Asus RT-G32 C1 - make a router out of it” or WIVE-NG-RTNL firmware for RT-G32 C1 Asus rt g32 installation disk

If you recently became the owner of an Asus RT G32 router and encountered certain problems during its connection and configuration, then you have come to the right site. In this article we will look at the most common problems, which you encounter when setting up this router, and we will also tell you about some operating tricks.

First, you must definitely ask your provider for the following configuration features that will be entered directly during setup: protocol (PPTP, L2TP, PPPoE), IP properties (static or dynamic, automatic or manual assignment of IP and DNS), as well as the presence (or absence) bindings network card by MAC address. It also wouldn’t hurt to find out if a special login and password have been set for logging into the router’s control panel.

In the next step, our path lies in the connection properties by local network (Control Panel - Network and Sharing Center shared access- our Internet connection - left-click on it - Properties). We look for “Internet Protocol Version 4 (TCP/IPv4), click on “Properties.” In the “General” tab, click “Obtain an IP address automatically” and “Obtain a DNS server address automatically.” Click “OK.”

At this point, you should already have an Ethernet cable connected from your computer to the router, in LAN connector 1. It is recommended to reset the settings before the first setup - this is done very easily: press the Reset button for 10 seconds.

The site will require authentication - login and password. If your provider does not set any specific data, then enter the standard ones - admin in the login and admin in the password. You can also find information on the login and password from the router control panel on the bottom of the router.

After all the operations, we find ourselves. First of all, indicate the protocol of your operator on the “WAN” tab in the “WAN connection type” line. If the address is provided automatically, we leave everything as is. If you need to register the IP address and DNS manually, then check the “No” box in “Obtain a WAN IP address automatically?” and enter the parameters below.

The main part setup is complete. Now - WiFi setup. This is the "tab" Wireless network" - "General".

• SSID - the name of your router;
• Hide SSID - whether you need to display the router name or not;
• Country code - select your country;
• Wireless network mode, Channel width - leave as is;
• Channel - it is advisable to set something other than automatic or the first - optimally 6 or 9. This setting will help you speed up your wireless Internet connection;
• Expanded channel - leave it as is;
• Authentication method is WEP, WPA or WPA2. The most modern is WPA2, so we install it. The rest of the settings are default.

You can also enter your own password in the " Pre-shared key WPA". That's all on this page - you can click "Apply".

Now go to “Administration”, where we click “Reboot” and “Exit”. The router will be completely ready for use after a reboot.

This is all we wanted to tell you about setting up a router of this model. If you have any questions, ask them in the comments and we will definitely answer them. See you on the pages of our website!

ASUS is a well-established electronics manufacturer with good characteristics, including modems for Internet access. But any device of this type must be configured to the parameters of the provider with whom the contract for the provision of communication services has been concluded.

This instruction will give you the answer to the question of how to set up asus router rt g32, it is worth remembering that the configuration algorithm and interface of devices from the same supplier are very similar, so the article will be useful to all buyers of ASUS modems with Wi-Fi support.

Preparing for setup

Technical preparation of the router for configuration is carried out in several stages:

1. Connect the power supply to the Asus rt-g32 and turn it on.
2. Connect the Ethernet cable provided by your provider to the modem connector labeled “WAN”.
3. Connect the router port labeled “LAN1” to the computer’s network card using an Ethernet cable, which is included in the Wi-Fi modem kit.
4. Reset the Asus RT g32 to factory settings by pressing and holding the “Reset” button recessed in the case for ten seconds.

Setting up your computer

Often the characteristics of a computer's network card are manually configured for other connections. To work with the Asus RT g32 Wi-Fi router, you need to configure the card:

1. Open the section network settings OS. For example, for Windows 7 you need to open the settings window shown in the following figure (located in the control panel), where you click on the highlighted link.

2. Go to the connection properties by right-clicking on its icon and selecting the appropriate item in the menu that appears.

3. Open “Properties” of the item indicated in the following figure:

4. Set the protocol characteristics as shown in the figure:

We repeat the procedure for the remaining connections, if any.

Setting up the router

To configure the Asus RT-g32 according to the settings of your provider, follow the steps of the following instructions:
1. Launch any browser, enter the address 192.168.1.1 and go to it.
2. In the loading authorization dialog, enter “admin” in both fields and click on “Submit”

3. Click on the “Go to Home Page” button

4. The software shell of the Asus RT g32 Wi-Fi router supports Russian, select it in the “Language” field.

5. To configure access options for the global network, click on the “WAN” main menu item.
6. Find out your connection type from your telecom operator.

7. If the provider provides the Internet using dynamic IP technology, then nothing needs to be changed on the “WAN” page. Click on the "Accept" button.
8. If the Internet is provided using static IP technology, then in the “Type” paragraph WAN connections» select the appropriate type and fill in all the form fields with the data received from the provider and click on “Accept”.

9. When choosing a type PPPoE connection indicate receiving an IP address automatically or fill in the address field if it was provided by your Internet provider. Z Fill out the fields in the “Settings” section account and connections" with the data specified in the contract for the provision of communication services, and in the MTU field enter the value 1472 and click on "Accept".

11. Apply the changes and configure the wifi module for wireless connection. If this option is not needed, reboot the modem and use the Internet.

Wi-Fi setup

To configure wireless settings in global network Open the “Wireless Network” tab of the main menu. Where you will set the following parameters:

1. In the “SSID” field, enter the name of the Wi-Fi network displayed on subscriber devices. It can be arbitrary, but must consist only of numbers, symbols and letters of the Latin alphabet.
2. Enable the “Hide SSID” option if you want to use this method of protecting your wifi networks from unauthorized access. When activated, the setting hides your network from subscribers, and you can connect to it only by knowing its exact name.
3. In the “Authentication Method” line, set “WPA-Personal”. And in the line " WPA encryption» select "TKIP". These are the most well-established and widely used methods of network security.
4. The “WPA Pre-Shared Key” line contains the password that users must enter when logging into your wifi network. The length of the code combination must be at least eight characters; any characters can be used.
5. To fix the settings, click “Apply”.

This completes the setup of the Asus RT g32, all that remains is to reboot it and use the Internet, both via a wired interface and via Wi-Fi.

Found a typo? Select the text and press Ctrl + Enter

The other day after unsuccessful firmware distributor ASUS RT-G32 (ver. C1) The device completely refused to work. It was impossible to even enter the device management page (I mean addresses 192.168.0.1 or 192.168.2.1 ). Tips on forums about restoring factory firmware using the program tftpd32 didn't help. To be honest, I began to fear that I would no longer have Wi-Fi and began to figure out in my mind what would be more profitable - to give my Asus to a workshop or to buy a new network distributor. However, the situation was alleviated by the leadership from one foreign network (the link will be below) - I’m translating the sequence of actions into Russian.

Note before you start - you will need O. With. Windows to perform these actions; For Linux, unfortunately, there is no manual.
No wireless device in recovery mode is found, device not found in recovery mode, ASUS RT-G32 firmware ver. C1, Asus Firmware Restoration, asus firmware 2.0.3.4, router, router, wifi, wifi

So:

1. Download the archive with the recovery program Asus Firmware Restoration and manufacturer's firmware ASUS_2.0.3.4(urgently on October 17, 2015):

2. Extract the contents of the archive, say, to the desktop;

3. Then connect the device directly to the network card - connect one end of the network multi-core (cable) to the computer, and the other to the connector LAN1 router (modem, if available, turn off for a while);

4. Enter the Network and Sharing Center (tray icon):

5. Click "Change adapter settings":

6. Disable all interfaces except "Local Area Connections" (LAN):

7. Open interface properties LAN:

9. Disable firewall Windows in the control panel (as shown in the picture), as well as third-party firewalls(Kaspersky, Komodo, Outpost, Avast, Nod32...):

The first part of the preparation is completed, and now the second part, the recovery itself:

10. Launch the program Rescue.exe from the previously unpacked archive and indicate in it the path to the firmware file RT-G32.C1_2.0.3.4.trx, But UNDER NO EVENT Don't press the button yet Download":

11. Check again that all wires (cables) are disconnected (including the power cord). Only the network multicore connecting the connector should remain LAN1 router and computer network card slot;

12. Press the button with a toothpick or ballpoint pen. Reset- press and hold until you release:

I took this picture from the page

One of the most popular router models on the domestic market. The basis of wide popularity is a reasonable balance of a sufficiently powerful signal, affordable price and ease of setup. However, some nuances arise here too - among the most common questions is traditionally called configuration.

Why do you need to update your router software?

Something to take into account right away - regular updates software plays a huge role for stable and efficient work each router. Required condition This means working with current version BY.

Otherwise, the likelihood of various software failures significantly increases - including freezing, incomplete functionality of the device, etc. Therefore, if the current version of the software becomes outdated, you should take care of updating the firmware - we will consider an effective approach for this.

Let's move on to the firmware - a simple procedure

Installation is carried out according to the following procedure:

How to check the functionality of the router after flashing and configuration

Next, we move on to the final stage of the router firmware - testing and making sure it works. Through this procedure, we have to determine whether the device allows access to the Internet. To do this, we adhere to the following testing order:

• Turn on the computer and router.
• You should wait until the connection is completed.
• It remains to launch one of installed browsers on your computer. Enter any site into address bar browser.
• The site should open in 10–15 seconds.
• If the firmware and setup were successful, you will be able to fully launch and view sites, otherwise you should repeat the firmware and setup procedures, making sure there are no errors.

Meet the Asus RT-G32 version C1, which was tested by Russian providers (although I have a hard time believing it). I would not recommend this router under any circumstances, since with standard firmware it is extremely unstable and very slow.

But somehow I got it. One fine day, they brought me this router and asked me to do something with it so that it would be normal, smiling, I said that I could try installing DD-WRT, but stable work I don’t guarantee it, since this is a budget device that shouldn’t be used as a SOHO solution.

Having looked at him more closely, I remembered something... It was back in 2011, we worked as operators in technical support, and we survived as best we could...

Preface

And we survived only because the management banned the Internet on our office PCs. But we are smart, not foolish, and we began to practice using personal laptops at work in the evening, and used it as a router to distribute this Internet. But since some “colleagues” liked to use torrents, the speed of our Internet was extremely disgusting.
Having blocked this “collector” on the router and sent it to a known destination, it was decided to install something stable on this router, and the choice fell on WIVE-NG-RTNL. That’s when the article was written (even though it was revision b1).

Is it really C1?

as you may have noticed, this is already the second article about this piece of hardware, but the previous, old article mentions revision B1, and we have revision C1.

Now, reader, take your router in your hands and look at the sticker: if there is an entry H/W ver.: C1, then you can continue reading this article , if there is something else, or this entry simply does not exist, close this article!

This is important because the router may fail! But if everything is fine and everything fits, we’ll continue.

Description

Well, now let's talk about the firmware of this device.

Why not DD-WRT? Since this router is based on the Ralink RT3050F chip, we won’t be able to just go to dd-wrt.com and download the firmware, since it simply doesn’t exist (although I tried). Someone may say that its firmware is possible, but if the official developer of dd-wrt said it is impossible, then there were reasons for that.

What is Wife-NG? Wive-NG is a series open firmware for devices on various chips from various vendors. If we compare this firmware with DD-WRT, then DD-WRT is a firmware that opens up a lot of functionality, and Wive-NG focuses on stable operation in unattended mode, while maintaining maximum flexibility and functionality.

Why change the firmware? Well, everything is simple here. If you, reader, are satisfied with the performance of your router, do not touch it and close this article. If you have to regularly reboot this router, or you are experiencing difficulties, and you do not have money for microtik, and playing Dota only adds gray hair to your beard, then the last chance is to flash the firmware of this router.

Firmware for this router

Straight to the point:

As a result, we got a completely different router :)

I will not dwell on the settings in detail, since a lot of guides have already been written before me on how to do this for any provider (I will provide links below). Just keep in mind that the password and login for the admin panel have changed to Admin / Admin (with a capital letter).